Nanjing Chemical Material Corp.
Service
Products

Polyether Polyol Manufacturing Process Polyether Polyol Manufacturing Process

Synthesis of DMC-based polyether polyol by a continuous method

A certain amount of DMC catalyst is taken and uniformly dispersed in a certain amount of small molecule initiator. Add 0.5 kg of the mixture of the initiator in the small test reactor. The vacuum was replaced 1-2 times with N2, and the N2 pressure was maintained at 0.1 MPa. After heating, stirring and raising the temperature to a certain temperature, the quantitative PO was introduced into the continuous autoclave with nitrogen gas for induction. When the induction is successful (the temperature in the kettle rises and the pressure drops), the PO is continuously passed to carry out the reaction. Open the outer loop and continue to pass the PO into the continuous kettle.

When the liquid in the reaction vessel is full, the PO, DMC catalyst and the initiator are continuously added to the kettle at a certain ratio and a certain speed through the power system. Continuous discharge is started when a certain pressure is reached in the continuous autoclave. Keep the feed rate the same as the discharge rate until all the stock is added. The crude product discharged from the kettle enters the aging kettle, and is heated, matured, degassed, and discharged to obtain a finished product.

Related Products Wiki
  • 2-Chloropropionic Acid

    2-Chloropropionic Acid

    September 23, 20212-chloropropionic acid is a pale liquid with a slight odor and is the simplest chiral chlorocarboxylic acid. The formula of 2-Chloropropionic acid is CH3CHClCO2H. It is produced by chlorination of pro...view
  • The Analysis of the Factors Influencing the Odor Production of Polyether Polyol

    The Analysis of the Factors Influencing the Odor Production of Polyether Polyol

    April 21, 2021Polyether polyol is an important macromolecule raw material, which is mainly used to make various polyurethane materials. In recent years, with the continuous improvement of production technology, the...view
  • Application of α-olefin Sulfonate

    Application of α-olefin Sulfonate

    April 21, 2020AOS (α-olefin sulfonate sodium salt) has very good comprehensive properties. It has mature technology, reliable quality and good detergency. Especially in hard water, it also shows the characteristic...view
  • The Properties of Bronopol

    The Properties of Bronopol

    July 6, 2020CAS: 52-51-7. With its English name, Bronopol, it is also known as bromo-2-nitro-1.view
  • Uses of Propionyl Chloride

    Uses of Propionyl Chloride

    May 17, 2021Propionyl chloride is a colourless to light yellow transparent liquid with a pungent odour, is soluble in water and ethanol and is violently decomposed. It is used for the following purposes:Applicati...view
  • An Introduction of Ethyl Iodide Cas No

    An Introduction of Ethyl Iodide Cas No

    September 24, 2020Ethyl iodide cas no is a colorless and flammable compound. Its chemical formula is C2H5I, which is prepared by heating ethanol with iodine and phosphorus. When it comes into contact with air, especial...view
Related Products
  • Polyethylene Glycol Product InformationProduct Name: Polyethylene Glycol 400 Chemical Formula: CAS No.: 25322-68-3Dangerous Grade: Technical Data:ITEMSSPECIFICATIONHydroxyl Number as mgKOH/g 267-295pH (5% Aq.solution) a...
  • Hexadecyldimethylamine Product InformationProduct Name: HexadecyldimethylamineChemical Formula:CAS No.: 112-69-6Dangerous Grade: 8Technical Data: ITEMSSPECIFICATION
  • Allyl Alcohol Product Name: Allyl AlcoholChemical Formula: C3H6OCAS No.: 107-18-6Dangerous Grade: 6.1Technical Data of Allyl AlcoholITEMSRESULTSAppearanceClear & FreeColour(Pt-Co Unit)
  • Fatty Acid Methyl Ester Ethoxylate (FMEE) Product InformationProduct Name: Fatty acid methyl ester ethoxylateChemical Formula: C18H36CO(OCH2CH2)7OCH3CAS No.: 65218-33-7Dangerous Grade: Technical Data:ITEMSSPECIFICATIONSOXFMEE-P812OXFMEE-P816O...
  • TEL:+86-25-52337978
  • EMAIL: info@njchm.com
  • ADDRESS:12/F, Block B, Technology and Innovation Building, Nanjing University of Technology, No.5 New Model Road, Nanjing 210009, China